? semiconductor components industries, llc, 2008 march, 2008 - rev. 2 1 publication order number: nlu3g14/d nlu3g14 triple schmitt-trigger inverter the nlu3g14 minigate is an advanced high-speed cmos triple schmitt-trigger inverter in ultra-small footprint. the nlu3g14 input and output structures provide protection when voltages up to 7.0 v are applied, regardless of the supply voltage. the nlu3g14 can be used to enhance noise immunity or to square up slowly changing waveforms. features ? high speed: t pd = 4.0 ns (typ) @ v cc = 5.0 v ? low power dissipation: i cc = 1 a (max) at t a = 25 c ? power down protection provided on inputs ? balanced propagation delays ? overvoltage tolerant (ovt) input and output pins ? ultra-small packages ? these are pb-free devices in a2 out y2 1 out y2 in a1 gnd out y1 in a2 figure 1. pinout (top view) figure 2. logic symbol v cc in a1 out y2 1 1 2 3 4 8 7 6 5 out y3 in a3 in a3 out y3 1 marking diagrams http://onsemi.com see detailed ordering and shipping information in the package dimensions section on page 4 of this data sheet. ordering information udfn8 case 517aj pin assignment 1 2 3in a2 in a1 out y 3 4 5 out y 2 gnd function table l h ay h l 6in a3 1 8 ux, a or la = specific device code m = date code = pb-free package uxm 7 out y1 8v cc 1 ullga8 1.45 x 1.0 case 613aa 1 ullga8 1.6 x 1.0 case 613ab 1 ullga8 1.95 x 1.0 case 613ac am lam lam
nlu3g14 http://onsemi.com 2 maximum ratings symbol parameter value unit v cc dc supply voltage -0.5 to +7.0 v v in dc input voltage -0.5 to +7.0 v v out dc output voltage -0.5 to +7.0 v i ik dc input diode current v in < gnd -20 ma i ok dc output diode current v out < gnd 20 ma i o dc output source/sink current 12.5 ma i cc dc supply current per supply pin 25 ma i gnd dc ground current per ground pin 25 ma t stg storage temperature range -65 to +150 c t l lead temperature, 1 mm from case for 10 seconds 260 c t j junction temperature under bias 150 c msl moisture sensitivity level 1 f r flammability rating oxygen index: 28 to 34 ul 94 v-0 @ 0.125 in v esd esd withstand voltage human body model (note 2) machine model (note 3) charged device model (note 4) > 2000 > 200 n/a v i latchup latchup performance above v cc and below gnd at 125 c (note 5) 500 ma stresses exceeding maximum ratings may damage the device. maximum ratings are stress ratings only. functional operation above t he recommended operating conditions is not implied. extended exposure to stresses above the recommended operating conditions may af fect device reliability. 1. measured with minimum pad spacing on an fr4 board, using 10 mm-by-1 inch, 2 ounce copper trace no air flow. 2. tested to eia / jesd22-a114-a. 3. tested to eia / jesd22-a115-a. 4. tested to jesd22-c101-a. 5. tested to eia / jesd78. recommended operating conditions symbol parameter min max unit v cc positive dc supply voltage 1.65 5.5 v v in digital input voltage 0 5.5 v v out output voltage 0 5.5 v t a operating free-air temperature -55 +125 c t/ v input transition rise or fall rate v cc = 3.3 v 0.3 v v cc = 5.0 v 0.5 v 0 0 no limit no limit ns/v
nlu3g14 http://onsemi.com 3 dc electrical characteristics symbol parameter conditions v cc (v) t a = 25 c t a = +85 c t a = -55 c to +125 c unit min typ max min max min max v t+ positive threshold voltage 3.0 4.5 5.5 1.85 2.86 3.50 2.0 3.0 3.6 2.2 3.15 3.85 2.2 3.15 3.85 2.2 3.15 3.85 v v t- negative threshold voltage 3.0 4.5 5.5 0.9 1.35 1.65 1.5 2.3 2.9 1.65 2.46 3.05 0.9 1.35 1.65 0.9 1.35 1.65 v v h hysteresis voltage 3.0 4.5 5.5 0.30 0.40 0.50 0.57 0.67 0.74 1.20 1.40 1.60 0.30 0.40 0.50 1.20 1.40 1.60 0.30 0.40 0.50 1.20 1.40 1.60 v v oh minimum high-level output voltage v in v t-min i oh = -50 a 2.0 3.0 4.5 1.9 2.9 4.4 2.0 3.0 4.5 1.9 2.9 4.4 1.9 2.9 4.4 v v in v t-min i oh = -4 ma i oh = -8 ma 3.0 4.5 2.58 3.94 2.48 3.80 2.34 3.66 v ol maximum low-level output voltage v in v t+max i ol = 50 a 2.0 3.0 4.5 0 0 0 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 v v in v t+max i ol = 4 ma i ol = 8 ma 3.0 4.5 0.36 0.36 0.44 0.44 0.52 0.52 i in input leakage current 0 v in 5.5 v 0 to 5.5 0.1 1.0 1.0 a i cc quiescent supply current 0 v in v cc 5.5 1.0 10 40 a ac electrical characteristics (input t r = t f = 3.0 ns) symbol parameter v cc (v) test condition t a = 25 c t a = +85 c t a = -55 c to +125 c unit min typ max min max min max t plh , t phl propagation delay, input a to output y 3.0 to 3.6 c l = 15 pf 7.0 12.8 1.0 15 1.0 17 ns c l = 50 pf 8.5 16.3 1.0 18.5 1.0 20.5 4.5 to 5.5 c l = 15 pf 4.0 8.6 1.0 10 1.0 11.5 c l = 50 pf 5.5 10.6 1.0 12 1.0 13.5 c in input capacitance 5.0 10 10 10 pf c pd power dissipation capacitance (note 6) 5.0 7.0 pf 6. c pd is defined as the value of the internal equivalent capacitance which is calculated from the dynamic operating current consumption without load. average operating current can be obtained by the equation i cc(opr) = c pd ? v cc ? f in + i cc . c pd is used to determine the no-load dynamic power consumption: p d = c pd ? v cc 2 ? f in + i cc ? v cc.
nlu3g14 http://onsemi.com 4 v cc gnd 50% 50% v cc a or b y t phl t plh figure 3. switching waveforms figure 4. test circuit *includes all probe and jig capacitance. a 1-mhz square input wave is recommended for propagation delay tests. c l* input output v h v in v out v cc v t+ v t- gnd v oh v ol v h v in v out v cc v t+ v t- gnd v oh v ol (a) a schmitt-trigger squares up inputs with slow rise and fall times (b) a schmitt-trigger offers maximum noise immunity figure 5. typical schmitt-trigger applications ordering information device package shipping ? nlu3g14mutag udfn8 (pb-free) 3000 / tape & reel nlu3g14amx1tcg ullga8, 1.95 x 1.0, 0.5p (pb-free) 3000 / tape & reel nlu3g14bmx1tcg ullga8, 1.6 x 1.0, 0.4p (pb-free) 3000 / tape & reel NLU3G14CMX1TCG ullga8, 1.45 x 1.0, 0.35p (pb-free) 3000 / tape & reel ?for information on tape and reel specifications, including part orientation and tape sizes, please refer to our tape and reel packaging specifications brochure, brd8011/d.
nlu3g14 http://onsemi.com 5 package dimensions udfn8 1.8x1.2, 0.4p case 517aj-01 issue o notes: 1. dimensioning and tolerancing per asme y14.5m, 1994. 2. controlling dimension: millimeters. 3. dimension b applies to plated terminal and is measured between 0.15 and 0.30 mm from terminal tip. 4. mold flash allowed on terminals along edge of package. flash may not exceed 0.03 onto bottom surface of terminals. 5. detail a shows optional construction for terminals. a b e d bottom view b e 8x b a c c note 3 0.10 c pin one reference top view 0.10 c a a1 (a3) 0.05 c 0.05 c c seating plane side view l 8x 1 4 5 8 dim min max millimeters a 0.45 0.55 a1 0.00 0.05 a3 0.127 ref b 0.15 0.25 d 1.80 bsc e 1.20 bsc e 0.40 bsc l 0.45 0.55 e/2 b2 0.30 ref l1 0.00 0.03 l2 0.40 ref detail a (l2) (b2) note 5 l1 detail a m 0.10 m 0.05 0.22 0.32 8x 1.50 0.40 pitch 0.66 dimensions: millimeters mounting footprint 7x 1 soldermask defined *for additional information on our pb-free strategy and soldering details, please download the on semiconductor soldering and mounting techniques reference manual, solderrm/d.
nlu3g14 http://onsemi.com 6 package dimensions ullga8 1.45x1.0, 0.35p case 613aa-01 issue a notes: 1. dimensioning and tolerancing per asme y14.5m, 1994. 2. controlling dimension: millimeters. 3. dimension b applies to plated terminal and is measured between 0.15 and 0.30 mm from the terminal tip. 4. a maximum of 0.05 pull back of the plated terminal from the edge of the package is allowed. a b e d bottom view b e 8x 0.10 b 0.05 a c c l 7x note 3 0.10 c pin one reference top view 0.10 c 8x a a1 0.05 c 0.05 c c seating plane side view l1 1 4 5 8 dim min max millimeters a --- 0.40 a1 0.00 0.05 b 0.15 0.25 d 1.45 bsc e 1.00 bsc e 0.35 bsc l 0.25 0.35 l1 0.30 0.40 e/2 note 4 soldermask defined* dimensions: millimeters 0.22 7x 0.48 8x 1.18 0.53 pitch *for additional information on our pb-free strategy and soldering details, please download the on semiconductor soldering and mounting techniques reference manual, solderrm/d. 0.35 1 mounting footprint pkg outline
nlu3g14 http://onsemi.com 7 package dimensions ullga8 1.6x1.0, 0.4p case 613ab-01 issue a notes: 1. dimensioning and tolerancing per asme y14.5m, 1994. 2. controlling dimension: millimeters. 3. dimension b applies to plated terminal and is measured between 0.15 and 0.30 mm from the terminal tip. 4. a maximum of 0.05 pull back of the plated terminal from the edge of the package is allowed. a b e d bottom view b e 8x 0.10 b 0.05 a c c l 7x note 3 0.10 c pin one reference top view 0.10 c 8x a a1 0.05 c 0.05 c c seating plane side view l1 1 4 5 8 dim min max millimeters a --- 0.40 a1 0.00 0.05 b 0.15 0.25 d 1.60 bsc e 1.00 bsc e 0.40 bsc l 0.25 0.35 l1 0.30 0.40 e/2 note 4 soldermask defined* dimensions: millimeters 0.26 7x 0.49 8x 1.24 0.53 pitch *for additional information on our pb-free strategy and soldering details, please download the on semiconductor soldering and mounting techniques reference manual, solderrm/d. 0.40 1 mounting footprint pkg outline
nlu3g14 http://onsemi.com 8 package dimensions ullga8 1.95x1.0, 0.5p case 613ac-01 issue a notes: 1. dimensioning and tolerancing per asme y14.5m, 1994. 2. controlling dimension: millimeters. 3. dimension b applies to plated terminal and is measured between 0.15 and 0.30 mm from the terminal tip. 4. a maximum of 0.05 pull back of the plated terminal from the edge of the package is allowed. a b e d bottom view b e 8x 0.10 b 0.05 a c c l 7x note 3 0.10 c pin one reference top view 0.10 c 8x a a1 0.05 c 0.05 c c seating plane side view l1 1 4 5 8 dim min max millimeters a --- 0.40 a1 0.00 0.05 b 0.15 0.25 d 1.95 bsc e 1.00 bsc e 0.50 bsc l 0.25 0.35 l1 0.30 0.40 e/2 note 4 soldermask defined* dimensions: millimeters 0.30 7x 0.49 8x 1.24 0.53 pitch *for additional information on our pb-free strategy and soldering details, please download the on semiconductor soldering and mounting techniques reference manual, solderrm/d. 0.50 1 mounting footprint pkg outline on semiconductor and are registered trademarks of semiconductor components industries, llc (scillc). scillc reserves the right to mak e changes without further notice to any products herein. scillc makes no warranty, representation or guarantee regarding the suitability of its products for an y particular purpose, nor does scillc assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including wi thout limitation special, consequential or incidental damages. typical parameters which may be provided in scillc data sheets and/or specifications can and do vary in different application s and actual performance may vary over time. all operating parameters, including typicals must be validated for each customer application by customer's technical experts. scillc does not convey any license under its patent rights nor the rights of others. scillc products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the scillc product could create a sit uation where personal injury or death may occur. should buyer purchase or use scillc products for any such unintended or unauthorized application, buyer shall indemnify and hold scillc and its of ficers, employees, subsidiaries, af filiates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, direct ly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that scillc was negligent regarding the design or manufacture of the part. scillc is an equal opportunity/affirmative action employer. this literature is subject to all applicable copyright laws and is not for resale in any manner. publication ordering information n. american technical support : 800-282-9855 toll free ?usa/canada europe, middle east and africa technical support: ?phone: 421 33 790 2910 japan customer focus center ?phone: 81-3-5773-3850 nlu3g14/d minigate is a trademark of semiconductor components industries, llc (scillc). literature fulfillment : ?literature distribution center for on semiconductor ?p.o. box 5163, denver, colorado 80217 usa ? phone : 303-675-2175 or 800-344-3860 toll free usa/canada ? fax : 303-675-2176 or 800-344-3867 toll free usa/canada ? email : orderlit@onsemi.com on semiconductor website : www.onsemi.com order literature : http://www.onsemi.com/orderlit for additional information, please contact your local sales representative
|
